Share
Pin
Tweet
Send
Share
Send
They transform clothes and accessories, making them devilishly seductive or romantic ...
Keep your posture!
You can easily make enchanting standing collars for blouses, dresses, pullovers with your own hands from the remains of lace and fabric ...
Neck circumference 38 cm
YOU NEED: a flap of white silk size. 20 x 60 cm; cream-colored chiffon flap size 15 x 180 cm; measured lace (lace tape) white with scallops on both sides, width 6 cm, length 1.20 m; 4 small buttons covered with fabric; sewing thread, needle for embroidery.
HOW TO MAKE: cut a collar detail from silk: a rectangle 40 cm long, 18 cm wide (including allowances). Fold the collar detail to a width of 9 cm, iron the fold, fold the part again in one layer.
From the remnants to cut oblique beiki shir. 2 cm, with a total length of 20 cm. Fold oblique in half lengthwise, stitch at a distance of 4 mm from the fold, do not cut the ends of the threads. To turn the steering wheel out, thread the ends of the threads into the embroidery needle and tie in a knot. Draw the needle with your ear forward through the steering wheel. Cut the steering wheel into 4 identical parts. Mark the upper hinged loop (from the steering wheel) directly near the fold of the collar, the lower one - at a distance of 8 cm below it (under the fold of the collar). Distribute the remaining 2 loops between the upper and lower at equal intervals. The size of the loops depends on the size of the buttons. Iron the right front edge of the collar inward to a width of 1 cm.
For quilling, cut 80 cm from the lace, iron the ends to a width of 1 cm inwards.Then lay folds on the lace with a depth of approx. 1.5 cm and iron. The length of the lace with the folded folds is 38 cm. Sweep the folds along one edge, mark this edge face to face on the long edge of the collar = upper edge.
Fold the collar along the ironed bend with the front side inwards. Sew along the left front and bottom edges (seam width 1 cm), grabbing the quilling and hinges. To turn out a collar and to iron. Paste the remaining tape onto the collar, tighten the ends at the front edges. Scribble the tape.
Fold the chiffon strip in half along the width with the wrong side to the wrong side; grind the long edge 5 mm wide. Unscrew the strip and iron so that the seam lies in the fold. Sew again at a distance of 7 mm from the seam. Unscrew and iron the tape. Stitch the ends in a tight, narrow zigzag. Mark the middle of the tape. Pin the tape 1 cm wide, combining the midline, pin under the bottom edge of the collar. Stitch the edge of the collar on the tape 1 cm to the front ends.
Sew on buttons according to buttonhole.
Kiss the pen!
Lush cuffs from measured lace give to a usual blouse retrosharm.
YOU NEED: a white blouse, lace braid with scallops on one edge, width. 12 cm, length 1.20 m; also 2 and 3.5 cm wide, 60 cm long; chiffon flap size. 10 x 85 cm, thread for sewing.
HOW TO MAKE: cut the lace into 2 identical parts. Measure on the blouse, having previously fastened, the width of the cuffs. Sew lace along a straight edge to the width of the cuffs, distribute the assembly evenly.On lace with a width of 12 cm, first lace with a width of 3.5 cm, then lace with a width of 2 cm. Start all the layers along an even edge.
From chiffon to cut out two strips of width. 5 cm, length 85 cm. Fold the strips to the width. 2.5 cm inside out. Sew the edges to the edge. Bend the stripes of the stripes to the edge on the even edges of the lace ribbons, leave the excess length of the chiffon stripes on both sides of the same length for the ties.
Black queen
A lace collar softens the austere look of a leather jacket.
STEP-BY-STEP INSTRUCTIONS (see left to right)
YOU WILL NEED: a leather jacket without a collar; measured lace with scallops on both sides, 15 cm wide, approx. 70 cm; various lace sockets - approx. 20 pieces; sewing threads, needle for leather.
STEP 1
Measure the size of the neck, add 15 cm to the obtained value and cut a length of this length from the measured lace.
STEP 2
Cut the ends of the lace diagonally (5 cm). Lay the shorter edge in the folds to the size of the neck. Sew lace rosettes.
STEP 3
Place a lace collar on the jacket around the neck, pin and sew manually.
Photo: Jan Schmidel (7); Catwalkpix.com (3); production: Bernadette Prehtel and Rushana Jennings.
Share
Pin
Tweet
Send
Share
Send